Blog Electronoobs review electronics arduino

My Blog

Last tutorials

All about Arduino PWM frequencies

Debug Arduino and ESP with PlatformIO

Homemade Best Two Hand Multimeter with Arduino

Homemade Baby White Noise Generator

Measure AC RMS with Arduino

ADVERTISERS

Welcome to my BLOG page 3/4 ←PREVIOUS PAGE NEXT PAGE→

Arduino Range & Digital Spirit Level

Andrei - JANUARY 9, 2019

How To Mechatronics YouTube channel presented his work this Arduino Range & Digital Spirit Level, inside of an Acrylic case ane with an i2c LCD to show the measure.
Continue reading →

Posted by Andrei, see Q&A page here.

Flexible battery Charger/Voltmeter

Andrei - JANUARY 3, 2019

Androkavo YouTube channel presented his work a flexible PCB of a battey charger and voltmeter that is quite interesting.
Continue reading →

Posted by Andrei, see Q&A page here.

Christmas tree PCB

Andrei - DICEMBER 17, 2018

Christmass is almost here. What I found is this simple project from Hacktuber YouTube channel who presented his work on a Christmas tree PCB. I hope you find this interesting...
Continue reading →

Posted by Andrei, see Q&A page here.

MIDI fader box made by Noteas and Volts

Andrei - DICEMBER 10, 2018

Noteas and Volts YouTube channel presented his work on a MIDI fader box. He made the PCB that holds 8 lineal sliding potentiometers to control MIDI and a 7 segement display.
Continue reading →

Posted by Andrei, see Q&A page here.

Brushed drone board gets V4.0

ELECTRONOOBS - DICEMBER 04, 2018

The brushed drone from past videos is now on version V4.0. This enw PCB has some special upgrades and I hope it will perform a lot better. See more here...
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

Smartwatch V2.0 under test...

ELECTRONOOBS - NOVEMBER 27, 2018

The board is ready but it has some errors. But the watch works. here is a small intro on what and how the wathc works. I hope you like it and stay tuned for version 3.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

Version V2.0 of my Smartwatch board

ELECTRONOOBS - NOVEMBER 20, 2018

I've designed the second version for this board since the V1.0 had some problems. This one is much better and I can finally make my smart watch.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

POV clock PCB with Arduino

ELECTRONOOBS - NOVEMBER 13, 2018

Marlon Nardi made this board for a POV or persistance of vision display for a digital clock made with Arduino. Make the PCB for a homemade POV clock with Arduino and LEDs.
Continue reading →

Posted by Andrei, see Q&A page here.

Portable soldering iron V3 - 2

ELECTRONOOBS - november 05, 2018

The 3rd version of my soldering iron is ready. I've also designed a 3D case and the final project looks so awesome. I hope this will be a Kickstarter in the future. It will bea kit with all the components so you could mount it and learn at the same time.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

Portable soldering iron V3

ELECTRONOOBS - OCTOBER 25, 2018

Yes, this is the third version for this project. I know, 3 versions is a lot. But there is always something to improve. That's why I've made this new baord. It is smaller, has improvements and looks quite good.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

My smartwatch board is here

ELECTRONOOBS - OCTOBER 16, 2018

I'm working on a new project. I want to make a smartwatch based on an Arduino. I've made my own board that will have a bluetooth module. The plan is to pair with a smartphone and get bluetooth data.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

HCC module based on Arduino

Andrei - OCTOBER 10, 2018

Small post on a baord by SeanHodgins where he designed an Arduino compatible small module with a preburned bootloader on it and that is very easy to solder and also very small.
Continue reading →

Posted by Andrei, see Q&A page here.

MOD_Boy game board based on Arduino

Andrei - OCTOBER 02, 2018

SeanHodgins suprise us once again with a new board he designed based on another smaller board that uses the ATmega chip just as and arduino. Now, we haev a game board.
Continue reading →

Posted by Andrei, see Q&A page here.

Current sensing board for drones

Andrei - SEPTEMBER 26, 2018

Very interesting project by Joop Brokking. In order to keep the flight safe for a drone, there is a sneed to measure the current that goes toe ach ESC for each motor.
Continue reading →

Posted by Andrei, see Q&A page here.

DIY Nixie Clock

Andrei - SEPTEMBER 18, 2018

This is an awesome DIY Nixie clock made by sjm4306. It looks nice, kind iov vintage and the board is designed by him and manufactured by JLCPCB.
Continue reading →

Posted by Andrei, see Q&A page here.

PCB brushless motor

Andrei - SEPTEMBER 09, 2018

Very interesting project by Carl Bugeja. This is a triple phase brushless motor made on a PCB. That makes the project very small so it could be used in different aplications.
Continue reading →

Posted by Andrei, see Q&A page here.

Portable iron V2.0

Andrei - SEPTEMBER 04, 2018

arduino portable soldering iron version 2

Electronoobs finally made his second version of the soldering iron and seams to improved it a lot. Here are some of the parts of the enw project. See more...
Continue reading →

Posted by Andrei, see Q&A page here.

Binary watch

Harakiri - AUGUST 28, 2018

This is a binary watch made by Sverd Industries. It uses a real tiem clock to get the time and a few LEDs to print the time. But the format is binary so you must know how to read the time.
Continue reading →

Posted by Harakiri, see Q&A page here.

Arduino based digital Watch

Electronoobs - August 20, 2018

I've made my own digital but analog loow watch that is mbased on Arduino. For that we need low power and also the internal clock 8MHz bootloader version for the ATMega328p-au chip.
Continue reading →

Posted by Electronoobs, see Q&A page here.

TS80 soldering iron

ELECTRONOOBS - AUGUST 17, 2018

Just received the new TS80 soldering iron. I've test it, and tear it down. Let's see the new improvements and how this iron performs.
Continue reading →

Posted by ELECTRONOOBS, see Q&A page here.

Homemade portable soldering iron V2.0

Andrei - AUGUST 12, 2018

Electronoobs is working on the second version of the portable soldering iron with some improvements. This is how it looks for now and the main characteristics. In my opinion, it looks great. See more...

Continue reading →

Posted by Andrei, see Q&A page here.

PCB Fabrication Process in JLCPCB Factory

Andrei - JULY 17, 2018

Established in 2006. JLCPCB Factory is the earliest prototype and small-batch PCB production factory in China. Now, JLCPCB has four PCB manufacturing sites. Come with us on a tour of the PCB fabrication process for a 2 layer board to find out how a PCB is made...
Continue reading →

Posted by Andrei, see Q&A page here.

First version, optic encoded CNC mill board

Andrei - JULY 12, 2018

EN is working for a while at his project of a optical encoded CNC machine that will use brushed DC motors and an optic swithc to count steps. The project will be very low cost. This is the design of the first board.
Continue reading →

Posted by Andrei, see Q&A page here.

PCB engrave or online order?

Andrei - JULY 11, 2018

EN made a few versions of this board for a brushed drone flight controller. The question is: would be better to order the design from prfessional manufacturers or make the homemade version with a PCB mill?
Continue reading →

Posted by Andrei, see Q&A page here.

Welcome to my BLOG page 3/4 ←PREVIOUS PAGE NEXT PAGE→

Affiliate Disclosure

ADVERTISERS